Others Products

HBM large funnel 4 liters

Content 4 Liter. |Dimensions 28 x 19 x 29,5 cm. |

HBM professional storage trays

All our products have a warranty of at least 1 year.

HBM High Pressure Airless Spraying Machine Paint Sprayer Wall Spraying Machine Set 1010 Watt

(1)

Do you want to apply wall paint to walls quickly and without streaks? This is easy with the HBM High Pressure Airless Spraying Machine Paint Sprayer Wall Spraying Machine. This special device sprays all types of sprayable wall paint without any problems on walls and walls under very high pressure through a ten meter long hose. Thanks to the sturdy metal stand, you can place the sprayer anywhere and it is an asset for both professional painters and DIY enthusiasts. The nozzle can be used both horizontally and vertically and it is possible to place various nozzles in the nozzle. The silicone inlet hose has a large, weighted suction mouth with filter at the end, so that no hard paint particles are sucked in. Suitable for both professionals and DIY enthusiasts Spray all types of sprayable wall paint on walls and walls without any problems Maximum output: 1.5 liters per minute Maximum spray pressure: 3000 PSI / 206 bar Dimensions: 38.5 x 27 x 43 centimeters Product specifications Power: 1010 Watts Maximum output: 1.5 liters per minute Maximum spray pressure: 3000 PSI / 206 bar Dimensions: 38.5 x 27 x 43 centimeters

HBM 200 kg. mdf transport dolly

(1)

Dimensions 580 x 300 x 100 mm. |Maximum load capacity 200 Kg. |Wheel diameter 50 mm. |

HBM electric liquid pump, siphon pump including batteries.

(1)

Material Kunststof. |Color Blauw / Zwart. |Tension 1,5 Volt |Capacity 560 liter/uur |Battery type R20P 1,5 Volt. |

HBM 1500 x 30 mm. impact iron

(1)

Total length 1500 mm |Diameter 30 mm |

HBM cement spray gun, mortar spray gun

(1)

This stainless steel mortar funnel gun is suitable for spraying different types of mortar, glass fiber reinforced concrete and other materials. Can be sprayed in a coarse 3 mm. grain up to 2.5 cm thick structural layers. It can also be used for applying other mortars such as exterior wall insulation mortar or loam. Most important features: Funnel made of stainless steel Installed 4-hole spray plate is easy to slide aside, remove and clean Swivel joint between handle and hopper for easy working Spray: Sand / cement slurries, sprayable mortars, grout, glass fiber reinforced concrete, fire resistant mortars and other materials Recommended compressor 340 liters per minute at 6.9 BAR

HBM 63 liter concrete mixer, concrete mixer

(2)

Nominal Voltage 230 Volt, 50 Hz. |Engine power 650 Watt. |Drum speed 27,5 O/min. |Drum content 63 Liter. |Drum opening diameter 267 mm. |Material Staal. |Overall dimensions 110 x 55 x 93,5 cm (L x B x H) |

HBM 6-layer shelf storage brackets, storage rack

(2)

The HBM 6 Layer Shelf Storage Brackets are a must-have for every workshop, garage or shed. The storage rack creates generous storage space for wood, pipes and other long items. It can be mounted both indoors and outdoors on fences, walls, etc. Technical data of the HBM 6 Layer Planks Storage Brackets, storage rack: Capacity - maximum load: 50 kg per level. Material - primary construction: Steel. Number of shelves: 6 Levels. Height: 1038mm. Length: 300mm. Weight: 7.49 Kg. Width: 300mm. The HBM 6 Tier Shelf Storage Brackets are easy to install and come with 12 racks, 12 end caps, 12 1/14" pan head screws 6 gauge, 2 posts and 6 spacers. With these storage brackets you create the ultimate storage space and keep your workshop, garage or shed organized and tidy.

HBM stainless steel oil drip plate, drip tray, oil collecting tray 600 x 400 x 48 mm.

(1)

Technical data of the HBM stainless steel oil drip tray, drip tray, oil catch tray 600 x 400 x 48 mm. Dimensions 600 x 400 x 48 mm. Ideal for parking your car or while tinkering. Made from SS201 stainless steel. Easy to clean.

HBM Vacuum Pump 1 Stage with 2-Fold Pressure Gauge Set 60 Liters Per Minute

This complete refrigerant set contains the HBM vacuum pump and the 2-fold pressure gauge set. The vacuum pump is designed for professional use in refrigeration and air conditioning systems. It creates a vacuum, which makes it possible to retrofit the air conditioning with refrigerant. The pump is suitable for refrigeration recovery, printing machinery, medical equipment, vacuum packaging, hot forming and other extraction work. The pump has an aluminum housing and a practical oil sight glass, with which you can check the oil level at any time. It also has an integrated handle for easy transport. The 2 way pressure gauge set is suitable for filling and inspecting air conditioning systems by reading system pressure readings. It is suitable for use on all automotive A/Cs, and commercial and domestic A/C refrigeration systems. The color coded gauges are quick, clear and easy to read. The gauges are encased in a protective bumper to prevent damage. You can use the integrated steel hook to hang the gauges quickly and easily. The pressure gauge set has a durable construction. Technical specifications: Voltage: 230 Volts Power: 180 Watt (1/4 HP) Suction power: 60 liters per minute Pump Speed: 2.5 CFM Rotational speed: 1,440 O/min Oil capacity: 250 ML Hose length: 152 cm Burst Pressure: 2,500 PSI Maximum working pressure: 500 PSI Suitable for refrigerants R134a, R22, R12 and R502 The HBM 1-stage vacuum pump with 2-fold pressure gauge set 60 liters per minute is supplied with 3 hoses, 2 quick couplings with an adapter for the car, and a gauge glass for checking the coolant.

HBM hydraulic wheel hub puller 10 tons

(2)

Technical data of the 10 ton HBM Hydraulic Wheel Hub Puller. Specially for stuck and rusted wheel hubs. 10 Ton hydraulic spindle For 4 and 5-bolt wheel hubs Hole diameter 96-125 mm Spindle hand control Suitable for: VW, Audi, Seat, Skoda, Opel, Volvo, Fiat, Renault, Peugeot and Citroen

HBM 12 volt electric diesel pump, fuel oil pump 175 watts

(1)

Engine power 175 Watt. |Voltage 12 Volt. |Engine speed 3600 O/min. |Pump capacity 45 Liter per minuut. |Maximum suction lift 3 Meter. |Maximum pump height 10 Meter. |

HBM adjustable construction prop with automatic locking 115 - 290 cm - 30 kg

The HBM Adjustable Building Prop with Automatic Locking is the ideal solution for supporting temporary structures and creating enclosed workspaces. It is a height-adjustable building prop with a simple, one-handed ratchet system and rotating panels. Fine-tuning swivel end cap to suit any surface Suitable for any surface Adjustable from 1.15 to 2.9 meters Maximum vertical capacity of 40 kg Plate dimensions of the stamp: 125 x 75 mm Equipped with automatic locking The building stamp is perfect to use in combination with polythene sheets to create a closed workspace. Thanks to the automatic locking, you don't have to worry about the safety of the construction, because the prop locks automatically as soon as it is at the right height. The HBM Adjustable Building Prop with Automatic Lock has a maximum capacity of 30 kg and is perfectly suited for supporting temporary structures such as walls, ceilings and timber frame construction. This building prop is designed for years of trouble-free use on the construction site.

HBM professional manual oil and liquid pump

Length of the pump 400 mm. |Diameter of the pump 70 mm. |Capacity 500 CC. |Length of the hose 280 mm. |

HBM suspension arm disassembly set

(6)

When keeping a control arm under control, while disassembling or assembling a ball joint or drive shaft, you, as a mechanic, have a shortage of hands. Often a piece of pipe has to be used, which unfortunately easily shoots away. This support arm tool solves all problems and allows you to do these jobs without the assistance of others. The hook is adjustable in height and length and reversible. Whoever learns to work with it, uses the support for all kinds of work, such as removing ball joints, controlling drive shafts, renewing bearing arm rubbers, repairs to struts etc. Technical data of the HBM support arm - mounting kit Material CR-MO steel. Total length 1180 mm. Adjustable u grip. Plastic handle

HBM 230 Volt Electric Bicycle Lift 100 Kg.

(7)

With the HBM 230 Volt Electric Bicycle Lift 100 Kg. you can easily lift bicycles and similar vehicles for maintenance, storage or repairs. Thanks to the central part and the various straps, the bike can be safely hung. Product specifications: Elevator dimensions: 29.7 x 112.2 x 17.2 cm (WxLxH) Maximum load: 100 kg Voltage: 230 V Frequency: 50 Hz Amperage: 2.0A Power: 450 W Remote control cable length: 3 meters Weight: 11 kg With this electric bicycle lift you make maintaining and repairing your bicycle a lot easier. The lift can carry a weight of up to 100 kg and is equipped with a handy remote control with a 3 meter cable. With the HBM 230 Volt Electric Bicycle Lift 100 Kg. you have your bike quickly and safely at the right height.

HBM mobile knee board

(1)

Technical data of the HBM Mobile Kneeboard. Dimensions: 50 x 26 cm. Maximum load: 150 kg. Delivered including: 5 wheels of 50 mm. Comfort foam. Magnetic tray 80 mm.

HBM motorcycle tire balancing device with adjustable legs

(1)

Now balance your motorcycle tires yourself with the HBM Motorcycle Tire Balancing Device With the HBM Motorcycle Tire Balancing Device with Adjustable Legs you can now balance your motorcycle tires yourself and prevent vibrations while driving. This device is suitable for all types of motorcycle tires. Below you can read more about the technical characteristics and the use of the HBM Motorcycle Tire Balancing Device with Adjustable Legs. Technical characteristics HBM Motorcycle Tire Balancing Device Adjustable legs for a stable and flat surface Spirit level for precise adjustment of the device Including shaft and clamping cones set for centering the motorcycle tire Conical clamping cones for perfect centering Easy and quick to balance Use of the HBM Motorcycle Tire Balancing Device To balance your motorcycle tires with the HBM Motorcycle Tire Balancing Device with Adjustable Legs, you must follow the following steps: Place the balancing device on a flat surface. If necessary, adjust the legs of the device. Make sure the appliance is level. Insert the axle through the rim and tighten the clamping cones with a 3mm Allen key (not included). Place the axle with the motor tire on the balancer and rotate the motor tire slightly. This way you determine where the motorcycle tire is heavier and where it is not. Mark the area where the tire is out of balance with tape or lead. Place the adhesive lead on the mark. Try to stick the adhesive lead with tape first, this will prevent the adhesive lead from falling while you have the motorcycle on its side stand. Rotate the tire slightly to check if the balance has improved. If necessary, repeat steps 5 and 6 until the motorcycle tire is perfectly balanced. With the HBM Motorcycle Tire Balancing Device with Adjustable Legs you can now balance your motorcycle tires yourself and save a lot of time and money. Order the device today and hit the road safely!

HBM mini pipe bender / pliers

Capacity 3, 4, 6 mm. ( 1/8", 3/16", 1/4" ) |Suitable for Koper, messing, zacht staal. |

HBM profi assortment box 38 x 31.5 x 6 cm

Dimensions 380 x 315 x 60 mm. |

HBM 4-piece professional impact-resistant crowbar set model 2

The HBM 4 Piece Professional Impact Resistant Crowbar Set Model 2 is an excellent choice for disassembly and assembly work. This set is equipped with a 2-component soft grip anti-slip handles for optimal grip. The set is suitable for both professional use and DIY enthusiasts. Technical specifications: Length of the crowbars: 200, 300, 450, 600 mm Width of chisel heads: 11, 16, 20, 20 mm Diameter of the handles: 30 - 35 - 35 - 35 mm In addition, this set is equipped with optimal power transfer with hand protection with an impact-resistant end cap. This ensures that the pry bar is easy to use and lasts a long time. The HBM 4 Piece Professional Impact Resistant Crowbar Set Model 2 is highly recommended for anyone looking for a high-quality and reliable crowbar set. Order today and experience the convenience of this set!

gaither tire fitting paste, tire grease white 5 kg

With the Gaither Tire Mounting Paste mounting tires becomes a piece of cake This tire grease is magnetic and makes it easier to spoon the tire over the rim Tire grease is a specially developed grease with short-term sliding properties The grease is applied with a goat foot or brush and will dry out after a short period of time so that the tire will not rotate relative to the rim After drying, this tire grease does not leave any unwanted grease residue The Gaither Tire Mounting Paste is suitable for run flat tires This product comes in a 5 kg white bucket With the Gaither Tire Mounting Paste, Tire Grease White 5 kg, mounting tires is child's play. The specially developed grease provides short-term sliding properties when the grease is applied with a goat foot or brush. The grease will dry out after a short period of time so that the tire will not rotate relative to the rim and will not leave any unwanted grease residue. This tire grease is magnetic and will ensure that the tire is easy to spoon over the rim. The Gaither Tire Mounting Paste is suitable for run flat tires and is supplied in a 5 kg white bucket. Go for an effortless tire mounting with the Gaither Tire Mounting Paste!

HBM 250 kg. record roller

Maximum capacity 250 Kg. |Clamping range Verstelbaar van 0 tot 23 cm. |Dimensions of the wheels 80 x 250 mm. |

HBM Professional Mobile Workshop Chair, Stool With 3 Drawers

(1)

Sitting and moving around the workshop, taking all your tools with you and everything running smoothly? That's what you can do with this handy mobile workshop stool! This workshop chair on wheels has a cupboard with 3 ball bearing drawers under the seat for storing tools and parts. At the back you will find a holder for spray cans, bottles or cups. At the front there is a bottom plate with a tray where you can quickly put something down. This way you always have everything at hand at any place in your workshop, while you can sit comfortably. Technical characteristics of the HBM Professional Mobile Workshop Chair, Stool With 3 Drawers Maximum load: 110 kg

HBM 200 mm. telescopic window squeegee, window squeegee with sponge 70-100 cm

Black window wiper on a telescopic handle that is adjustable / extendable from 70 to 110 cm long. The window wiper head has 2 sides: 1 with a sponge that is reinforced with a net structure, for removing stubborn dirt and insects from the window. And 1 side with a trigger for drying the window. Technical data of the HBM 200 mm. Telescopic Window Wiper, Window Puller with Sponge 70-100 cm. Width of the wiper head and trigger 20 cm. Total length of the stem Adjustable from 70 to 110 cm.

HBM deluxe motorcycle tire balancing device with adjustable legs

(3)

The HBM Deluxe Motorcycle Tire Balancing Device with Adjustable Legs is a handy and effective device that you use for balancing motorcycle tires. It comes with an axle and clamping cones set, so that the motorcycle tire always remains centered. With this device you can quickly see where the motorcycle tire is heavier and where it is not. The shaft has a diameter of 12 mm and the cone has a diameter of 15 mm. at its narrowest point and 35mm. on the widest part. The width of the rim that you can tension is 9 inches. The following technical data applies to the HBM Deluxe Motorcycle Tire Balancing Device with Adjustable Legs: Shaft diameter: 12mm Cone diameter: 15mm. at its narrowest point and 35mm. on the widest part Rim width: 9 inches To set up the balancer, place it on a flat surface. If this is not the case, the balancing device can be adjusted by means of legs. By means of the spirit level you can immediately see whether the device is straight or not. Then slide the axle through the rim and tighten the clamping cones (3 mm Allen key, not included). Once the clamping cones have been tightened, place the axle with the motor tire mounted on it on the balancer. With a slight twist on the motorcycle tire you will soon find out that the tire is not or properly balanced. The heavy part of the motorcycle tire will go down and the light part will go up. You can adjust the light part by means of adhesive lead. Tip, first attach the adhesive lead with adhesive tape or tape. The adhesive lead adheres well to the rims, which saves you a lot of effort and money. Once you have found the correct weight, stick on the adhesive lead. With the HBM Deluxe Motorcycle Tire Balancing Device with Adjustable Legs you can easily balance your motorcycle tires. You can set the device on a flat surface or by means of feet and the spirit level shows immediately whether the device is straight or not. Then slide the axle through the rim and tighten the clamping cones. You can quickly see where the motorcycle tire is heavier and where it is not, after which you can adjust the light part with sticky lead. This way you always keep your motorcycle tires in balance!

HBM 3 meter telescopic washing brush with water connection

This washing brush from the HBM brand is ideal for cleaning cars, vans, caravans, trailers, bicycles and other vehicles and objects around the house. The brush is lightweight and easy to use because of the extendable handle that extends up to 3 meters and is equipped with a comfortable handle. Important instructions Only use this product with cold water to avoid burns. Avoid power lines and wires. First remove the coarse dirt with water to prevent damage to the brush and the cleaning surface. The washing brush is easy to connect to your water supply, so that you can start your cleaning job immediately. Thanks to the brush, you can clean in a targeted and efficient way. The water supply is easy to regulate with the on/off button on the handle. With the HBM 3 Meter Telescopic Washing Brush With Water Connection you are therefore able to quickly and thoroughly clean your vehicles and other objects around the house. Order this product today for a competitive price and make the job easier and more fun!

HBM exhaust spring extractor

Total length 140 mm. |Material Gehard stal. |

HBM tornado professional vacuum cleaning gun with 5 nozzles

Sound 95 db( a) |Capacity Cup 1.0 liter. |Air connection 1/4" |Material PVC. |Lance Metaal. |Dimensions 325 x 130 x 235 mm. |